Showing results: 436 - 450 of 1660 items found.
-
JT 2122/MPV -
JTAG Technologies Inc.
The JT 2122/MPV DIOS (digital I/O scan module) increases the coverage and improves the diagnostic resolution of boundary-scan testing by extending test access to connectors and/or test points. JT 2122/MPV DIOS provides bi-directional parallel-scan access to up to 128 or 133 I/Os in a standard DIMM-168 module.
-
N19303B -
Keysight Technologies
The new Physical Layer Test System (PLTS) 2024 is the industry standard for signal integrity measurements and data post‑processing high-speed interconnects, such as cables, backplanes, PCBs, and connectors. Signal integrity laboratories worldwide have benefited from the power of PLTS in the R&D prototype test phase.
-
85039B -
Keysight Technologies
The Keysight 85039B calibration kit, with option M0F, contains male and female type-F open, short, and load standards. This calibration kit works with all 75 ohm network analyzers and test sets for measurement of devices with 75 ohm type-F connectors. The kit also includes type-N to type-F adapters. More economical versions of this kit are available by ordering option 00F for the female standards only, or option 00M for the male standards only. This kit is specified from dc to 3 GHz.
-
KRD41 series -
CME Technology Co. Ltd.
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
SKS-0506IB -
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0506IB1 fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; provides a pulse test voltage of up to 6kV; both AC and DC samples can be tested , subject to The rated voltage of the test equipment can reach 400V, and the rated current of the three-phase equipment is higher than 32A; 7-inch color LCD touch screen, friendly human-computer interaction interface, more intelligent and more user- friendly operation; the software is built in the IEC standard Level mode can be directly called.
-
SS30 -
Bemco Inc.
Bemco's Standard SS30 Salt Spray and Fog chamber meets all standard military, commercial, and ASTM salt fog corrosion and humidity corrosion tests. The SS30 is currently in redesign to incorporate a clear - see through top with the same advanced features of the previous fiberglass system. This chamber has a workspace of 48-inches wide by 36-inches high by 30-inches deep.
-
TH2689A -
Changzhou Tonghui Electronic Co., Ltd.
TH 2689/TH2689A provides max. test voltage: 800v/500v, charge current: 0.5mA─500.0mA( if >100V, the max. power 50W can limit). It is mainly applied in capacitance leakage current, insulation resistance and aluminum electrolysis capacitance anode foil pressure test. Also it can be applied in the confirmation of annihilator, zener diode, neonbulb .etc and leakage current test. Standard Handler interface, stable and rapid test, to reach the sorting effect
-
VI Tester -
JKI
VI Tester is a software test framework for LabVIEW that allows software developers to test their LabVIEW code (VIs). Software testing is a critical component of agile development and test driven development processes and is also critical for validating software functionality. VI Tester is based on the industry standard xUnit software test architecture that is used in many other programming languages. This architecture is very flexible and powerful, but also very easy for beginners to learn.
-
CalEasy Series -
Marvin Test Solutions, Inc.
CalEasy is a full-featured, Calibration Executive software package that supports the verification and calibration of Marvin Test Solutions instruments. The software is intended for use by users that prefer to perform in-house calibration and verification for their Marvin Test Solutions instruments. By calibrating or verifying the instrument in-house, the time and cost associated with returning an instrument to Marvin Test Solutions for calibration service can be eliminated or reduced. CalEasy is also used internally by Marvin Test Solutions production to perform initial calibration and to recalibrate the instrument when received for service. This ensures that user and factory based calibration performance is similar. Depending on the specific instrument, standards instrumentation supported for calibration / verification includes a DMM, and a frequency standards module. Some modules require the use of matrix switch card.
-
Barnes International Ltd
Test Limit Cards (and tickets) are nominally encoded to ISO standards BUT WITH specific parameters deliberately set to predetermined levels, which can be inside or outside the ISO limits. The Test Limit Cards are designed for use by Test\Inspection Departments, Field Service Engineers, Reader \ Encoder Development Engineers to check and confirm proper operation of magnetic stripe reading equipment (e.g. ATMs and POS).
-
Qualitest International Inc.
Qualitest offer the largest Hardness Test Block selection in the industry. If you don't see what you're looking for, please call our sales department. All of our Hardness Test Blocks come with Certification. All the blocks are calibrated and accredited to ISO guide 25 and will meet automotive and aerospace standards. The HRC test blocks are calibrated on the new NIST level.
-
6800 -
Instron
The 6800 Series Multi-Station System offers enhanced throughput with its ability to perform simultaneous, independent tests on up to five (5) separate specimens using a single load frame. Based on our standard 68TM-30 testing frame (30 kN capacity)*, this system is especially suitable when test times are lengthened due to high elongation or slow test speeds.
-
DataView -
Test Spectrum, Inc.
DataView is a low‐cost test data analysis tool that is used by test and product engineers to perform characterization of integrated circuit devices. DataView reads in industry standard STDF or ATDF files and can produce reports, histograms, and wafer maps in multiple formats including Excel. DataView is ideal for the test or product engineer who needs a fast and simple tool to analyze characterization data.
-
Magnetic Analysis Corp
Accurate handling, conveying and positioning of material, before, during and after the test is a critical part of any NDT system. MAC’s mechanical handling products, the result of many years of experience with actual NDT installations, help to ensure accuracy and successful test results. Standard and custom-designed options are available, plus “V” Roll and Constant Center Triple Guide Roll Test Benches.
-
CX-YB06 -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 plug power cord bending test machineThe power cord bending tester is used to bend (bend) the power cords of non-reconnectable plugs and household appliances and similar appliances.It complies with UL817, VDE0620, IEC60884-2006 Figure 21, and other standard requirements.The device can preset the number of tests (up to 999999 times), the test is automatically carried out, and when the te
